Maytag Bravos washer problems can be solved easily using the tips indicated in this guide. Although it is designed precisely to last over a decade, certain issues might occur as they are not completely immune to problems. However, proper maintenance can increase the longevity of these washers. Follow these procedures to troubleshoot your washer and optimize its function. Make sure to unplug the appliance from power before you conduct the inspections and replacement of parts.
Washer Won’t Spin or Agitate
Contents
If your Maytag Bravos washer won’t spin, then you need to check several components to determine the exact cause. You can start by checking the lid assembly of the washer.
Lid Switch Assembly
If the washer lid is open, it will not convey the electrical signal to start the cycle. It is a safety precaution used to avoid injury and water leaks through it. So if your washer won’t spin, you should first check whether the lid is closed and latched properly. If the lid is defective, the washer won’t start function either. So check the continuity of the lid switch assembly, and if it is defective, you would have to replace it.
Drive Belt
The drive belt should be in good condition for your washer to spin and agitate. So if the belt is loose, worn out, or damaged in any form, it would not function and needs to be replaced.
Motor Coupling
The motor is connected to the transmission with motor coupling and is a necessary system for the washer. If the washer is overloaded, the motor coupling will fail to protect the motor and transmission. Likewise, a damaged or worn-out motor coupling would not allow the washer to spin. So, check for damaged motor coupling and replace it.
Door Latch
The door should be closed and latched properly for extra security. Your Maytag Bravos washer won’t spin or agitate if the latch isn’t shut properly or defective. Since the door latch can fail both mechanically and electrically, it is necessary to inspect the door latch properly. Test it with a multimeter, and if there is no continuity when activated, you would need to replace it. If the door latch is damaged physically and hence doesn’t close properly, replace it with a new one.
Motor Control Board
The motor control board is the main controlling unit of the motor that transmits signals to the motor to start when necessary. So your washer would not start if the motor control board is problematic. First, check whether the control board sends signals to the motor using a multimeter. If it has no continuity and fails to send signals, it is defective and should be replaced.
Making a Loud Noise
If your Maytag Bravos washer makes loud noises when operating, you would have to be concerned about it. Do not leave it unattended as it would cause additional issues.
Bearing
The tub bearing is in the middle of the outer tub, and the inner tub should spin smoothly for correct performance. The washer would be very noisy if this bearing becomes worn out or damaged. Replacing the tub bearing would have to be done by disassembling most parts of the washer. Therefore, replacing both the inner tub and outer tub bearing is recommended when replacing the tub bearings.
Drive Pulley
Another reason why your washer might be noisy is due to a cracked or worn-out pulley. So check your drive pulley and replace it if damaged.
Drive Belt
The drive belt might crack or wear out over time and sometimes would burn out and cause a loud sound when running. So if you observe any such faulty conditions in your drive belt, you should replace it with a new one.
Motor Coupling
This is used to connect the motor with the transmission of the machine and fails if the washer is overloaded. Thus, it protects the motor and transmission. And this would also fail due to normal wear over time. So, check the motor coupling if your washer is noisy and replace it if damaged.
Washer not Draining
A washer would not drain mainly due to obstructions on the draining system. You can check this by observing the following components.
Drain Pump
The drain pump drains out used water with the help of an impeller. So if the pump fails, your washer would not drain efficiently. This might mostly occur due to obstructions and need to be cleaned to get back to proper function. If you find that the drain pump is noisy, then you would have to replace it.
Clogged Drain Hose
If your drain hose is clogged with small pieces of clothes or other debris, water will not drain. So, remove the hose, check inside it, and clear out any obstructions with a high-pressure water stream. Also, straighten out any bends or twists on the hose. If the drain hose is damaged, you might have to consider replacing it.
Door Lock
Like other modern washers, the Maytag Bravos washer would run only if its door is latched properly. So a problematic door lock or switch would also cause draining problems. So check the door lock for continuity with a multimeter and replace it if it is defective.
Water Pump Belt
A worn-out pump belt might also cause your washer to have draining issues. But the newer models do not have a water pump belt but come with a direct drive system. So before you check this, make sure which component is available in your model of washer.
Vibrating or Shaking Problem
Vibration is another common issue among the Maytag Bravos washer problems. You can check the following reasons to identify how to prevent your washing machine from shaking and vibrating.
Shock Absorber
It is normal for the washing tub to vibrate during its operation, and the shock absorbers reduce the shakiness by absorbing the vibration. So if shock absorbers are worn out or broken, your washer would shake noticeably. Therefore, check for any damaged shock absorbers and replace them.
Suspension Rod
Your Bravos washer consists of some suspension rods to reduce the vibration of the washtub while running. However, the washer will vibrate if one or more suspension rods are broken. So, check and replace the suspension rods if necessary.
Counter Balance Spring
Counterbalance springs are used to balance the motion of the washer tub by absorbing the movement while operating. This spring would break down over time, and the washer would start to vibrate excessively. So you need to check the counterbalance spring and replace it if broken. Replacing all the spring would help you to avoid future problems.
Suspension String
The suspension string also dampens the vibration of your washer. So check whether these are broken and replace them if necessary.
Rear Drum Bearing
The rear drum has bearings to ensure smooth movement of the inner tub. If this is defective, it will create excessive vibration and sound. You can refer to the user manual to find how to access the bearings and replace them. If your washer model does not allow changing bearings without an outer drum, both components would have to be replaced.
Washer Fills Slowly
If your Maytag washer fills slowly or does not fill at all, you need to check out the possible causes indicated here.
Water Inlet Valve
The Bravos washer is automated, and water is taken from its inlet valve when needed by the machine. However, if the inlet valve is defective, it would fail to fill efficiently or won’t fill at all. So, try cleaning the inlet valve screen, and if your washer still fills slowly, replace the valve.
Low Water Pressure
The water inlet valve would work only if the water supply of your home has enough pressure. So if it has a water supply below 20 psi, it would not fill the washer properly. So you need to increase the water pressure and check whether the problem is solved.
Maytag Washer Leaking Water
If your Maytag washer has water leaking problems, then it might be due to the following issues. First, check which of them has caused your washer to leak.
Drain Pump
If your drain pump is damaged, the washer would not drain the water properly and cause the washer to leak. Check whether it is damaged or has a broken bearing and make the necessary replacements.
Tub Seal
The washer tub would get damaged and leak water due to manufacturing errors or with time. If it continues, it will result in bearing failure, and therefore, it is beneficial to replace both the tub seal and the tub bearings. Since you have to disassemble most of the washer parts, it is better to look for other possible causes behind the leaking problem before changing the tub seal and tub bearing.
Door Boot Seal
A defective door boot seal might also leak water due to being worn out with time. So, check whether the door boot seal is damaged and replace it if needed.
Drain Hose
If the drain hose is defective, it mainly leaks from the back part of the washer where the hose is connected. So, inspect its connection and properly fix it to check whether the problem is solved. To avoid damages, make sure that the drain hose does not rub it against the wall.
Bravos Washer Won’t Start problem
This is one of the most common issues among Maytag Bravos Washer Problems. There are several possible causes behind this, and you can troubleshoot as described.
Timer
Your washer will fail to start if it has a defective timer, as it would not transmit the necessary electric signals. You can check this for continuity using a multimeter and replace it if faulty. However, as this might be a rare occurrence, it is recommended to check other possible faulty components before checking this.
User Control and Display
Your Maytag washer won’t start if the control board gets defective. You can test the control panel by pressing the buttons, and if some of them do not respond, then the control panel and display board would be defective. You can also check the power connection to these components, and if they get power and not functioning, then the display and control need to be replaced.
Line Fuse
The line fuse is contained in the home electric outlet panel for security purposes. If it senses an overload, the fuse blows out to protect the circuit from getting damaged. Inspect the fuse with a multimeter and if there is no continuity, replace it.
Main Control Board
The main control board controls all the functions of the appliance, and if it becomes defective, it will not perform correctly. But this is the least defective component in a washing machine. So, before checking it, make sure to check all other parts that could be defective.
Thermal Fuse
The thermal fuse blows away due to overheating and saves your washer. If this happens, your appliance will fail to start, and the fuse needs replacement. You can test this thermal fuse for continuity with a multimeter, and if there is no continuity, you need to replace it. But before you start the washer, check and solve all other issues that might have caused the thermal fuse to blow off.
Incoming Power Problem
Sometimes it might not be due to Maytag Bravos washer problems, but because it doesn’t get power from the supply. So you need to confirm that the outlet board has an active fuse and the home electric circuit breaker is switched on. You can also test the board by plugging in other appliances and checking whether they are operating.
Door Lock
Even though your washer gets power, it won’t start until its door is closed properly. A defective door lock prevents the washer from starting as a safety measure. The door lock functions mechanically with electric power and hence can fail either electrically or mechanically. Test the continuity of the door lock with a multimeter and replace it if it doesn’t have continuity.
Power Cord
Even if your home electric outlet has power, your washer will fail to start if it doesn’t get power correctly. This might be due to the use of a low-quality power cord. It is recommended to use a power cord that the manufacturer recommends.
Washer Overflowing Problem
If your washer overflows when being filled, it might be due to the following reasons. Check them to identify the cause for this.
Water Inlet Valve
You can identify a defective inlet valve by switching off the power while the washer is getting filled. However, if it continues to fill water, its water inlet valve is defective despite having no power. Replacing the valve would solve this overflowing problem.
Pressure Switch
The pressure switch is responsible for shutting down the power when the water reaches a certain level. If this gets defective, it will not function, and hence, the water would continue to fill and get overflowed. This can be corrected by replacing the pressure switch and making sure to check that the pressure switch’s air tube has no debris and any other leakages.
Low Pressure
For a water inlet valve to function properly, it requires a minimum water pressure of 20 psi. If your house’s water supply does not support this pressure, it would cause the inlet valve to be defective and overflow the washer. Therefore, check your water supply pressure and ensure this minimum value.
Frequently Asked Questions
How long should a Maytag washer last?
A Maytag washer is designed to last at least 10 years.
How do I reset my Maytag Bravos XL washer?
If you encounter Maytag Bravos XL washer problems, you can reset it using the steps indicated here.
- Press the Power/ Cancel button.
- Push the specific button to choose a new cycle.
- Press Start/ Pause, and you have reset your Maytag washer.
How do I reset my Maytag Bravos MCT washer?
Maytag Bravos MCT washer troubleshooting would sometimes require a master reset. To reset this, unplug the appliance from the power outlet and leave it for about one minute. Then plug the washer to power and open and close the washing machine’s door 6 times within 12 seconds. This would send a “reset” signal to all the components, thus resetting your washer.
How do I reset my Maytag Bravos washing machine?
If you conduct a Maytag Bravos X washer troubleshooting, you can reset it by following these steps.
- Unplug the washer from the electrical outlet and leave it for one minute.
- Plug the washer back in and continue lifting and lowering the lid 6 times within 12 seconds. This lifting and lowering of the lid should be started within 30 seconds.
- This would reset the motor, and you can start a new cycle.
Conclusion
These solutions can help solve your Maytag Bravos washer problems practically. As you can now solve your issues, you would only need to purchase the required parts. But if you find the replacement complicated and difficult to be handled alone, you should contact your technician for support. If your washer needs to be replaced, make sure to avoid these Worst Washing Machine Brands when purchasing.
You would find similar useful articles when troubleshooting why your Maytag Dishwasher Won’t Start.