The reason for your Frigidaire refrigerator water dispenser not working is often caused by a defective component. However, this might also be due to inadequate power supply to the component. So start by checking the availability of power at the socket outlet. Since this problem can cause damage to your appliance if left unattended, make sure to find the cause and fix it as soon as you figure it out. So let’s find out the possible causes that might lead to the improper functioning of your refrigerator’s water dispenser.
Frigidaire Refrigerator Water Dispenser Not Turning On
Contents
If your Frigidaire refrigerator is not turning on, you can troubleshoot it as indicated here. But, first, check the parts indicated here to diagnose the problem.
Frozen Water Tube
Sometimes, the refrigerator’s water tube might get frozen, causing the water dispenser to not work properly. If you figure out that this is the problem with your appliance, you can disconnect the power supply and then remove the water tube from the fridge. Next, use a hair dryer or leaf blower and circulate air through the tube to melt the ice. After fixing this problem, make sure to adjust your freezer temperature between 0 ˚F and 10 ˚F, which is the optimal temperature to prevent this from happening again.
Water Inlet Valve
The water inlet valve supplies the required amount of water to the dispenser and ice maker by turning it on and off at the required time. Water flows into the dispenser at a pressure of 20 psi, regulated by the water inlet valve. The water supply in your house should also have a pressure of at least 20 psi. So, if the water pressure is below this value, the dispenser may not work properly.
So check the water pressure of your house water supply, and if it has the necessary pressure, then the problem is in the water inlet valve. To check the function of the inlet valve, you can test it for continuity using a multimeter. If it shows continuity, then the valve is not defective, and you need to check another possible defect why your refrigerator won’t start. The water inlet valve should be replaced if it does not show continuity.
Dispenser Control Board
The dispenser control board manages all of the functions of the dispenser system. If it is faulty, your water dispenser will not work. However, this is a rare case, and the other components should be checked before you come to this. If you check everything else and find out that the dispenser control board is defective, the better option is not to repair it but to replace it with a new one.
Dispenser Switch
The Frigidaire refrigerator dispenser problems could also be due to a defective switch that transmits the voltage signals in the system. As there are several switches, even if one is burnt or damaged, the whole dispenser system would be out of order. You can check it physically for any defects and then conduct a continuity test using a multimeter. If it shows no continuity, then you need to replace the switches. Test the function of your dispenser after the replacement to confirm that the issue was solved.
Water Filter
The water filter of your refrigerator dispenser is responsible for screening out impurities and ensuring the safety of water dispensed through it. However, it can get clogged while filtering out the dirt over time and result in the Frigidaire refrigerator not dispensing cold water when required. Therefore, you need to replace your refrigerator’s water filter every six months to prevent it from getting clogged and damaging the dispensing system.
Door Switch
If the refrigerator door switch gets defective, the water dispenser will also not function as it turns off with the door switch. You can check the function of the door switch using a continuity test. If the door switch is defective, there will be no continuity, and you need to replace it with a new one. Make sure to get these components according to the correct model number of your refrigerator.
Water Dispenser Lever Broken
Your Frigidaire refrigerator water dispenser may not work if the dispenser lever is broken. Follow these steps to fix this broken lever.
- Before starting, disconnect the Frigidaire refrigerator from power and remove the drip tray from the freezer section.
- Then insert a putty knife at the bottom and bring down the façade. Memorize the arrangement before you disconnect the dispenser switches, and you need to know it when rewiring after the lever is fixed.
- After this, remove the dispenser light bulb and its switch.
- Remove the delay mechanism, open the cute door and pull out the defective lever.
- Place the new lever in the correct position and secure it with the screws.
- Reattach the delay mechanism to the door and rewire the dispenser switch. Ensure that the top of the dispenser façade is aligned correctly with the edge of the dispenser housing.
- Finally, insert the drip tray and connect the power supply of your refrigerator. Check whether the new lever is working properly.
Dispenser Turns on by Itself
This is another common occurrence among Frigidaire refrigerator dispenser problems. If your water dispenser turns on automatically by itself, this might be due to a defect in the water inlet valve. You need to replace it with a new water inlet valve that matches the model number.
Water Dispenser is Very Slow
Sometimes the problem is not that the Frigidaire water dispenser is completely not working, but it is so slow than usual. As a result, you might have to wait for a few minutes longer than before to fill a glass of water. If this is the case, you need to check the following possibilities and troubleshoot them.
Water Line
First, check whether there are any bends or kinks in the water line obstructing the water flow. If the water line is damaged due to these occurrences, you need to replace it to ensure the correct speed of water flow in your dispenser.
Insufficient Power Supply
Sometimes, the dispenser may not discharge water as needed if the refrigerator doesn’t get the required power supply. So check the power supply to your refrigerator, and if it has no issue, you need to check the next component.
Clogged Water Filter
Another reason why water is dispensed slowly from the water dispenser might be due to a clogged water filter. As it traps impurities and keeps your water clean, it should also be cleaned and renewed after some time. So check the water filter and replace it if needed.
Frigidaire Refrigerator Dispenser Lock Out
Your Frigidaire refrigerator dispenser will not work if it is locked. This is a safety feature activated to prevent unwanted opening of the dispenser. However, it might sometimes get activated automatically and cause trouble for the user. Nevertheless, you can deactivate this mode easily. You will find the Control Lock button next to the Light button. Press and hold it for about three seconds to activate or deactivate the Lock mode.
Frigidaire Refrigerator Water Dispenser Stuck
Another reason for your Frigidaire refrigerator water dispenser not working is because it is stuck. This happens when the dispenser chute is clogged. Check it and remove any possible obstructions blocking the water flow in the chute. If you see that the chute is twisted and damaged, you will have to replace it.
Frequently Asked Questions
What to do if Frigidaire refrigerator water dispenser not working after replacing the filter?
Check whether the filter is tightened properly. If you find something wrong, try removing the filter completely and then reinstall it tight. Check whether the gasket or the seal on your refrigerator water filter housing had moved when you replaced the filter. Sometimes this might be causing the issue.
How to clean Frigidaire refrigerator water dispenser?
To clean this, disconnect the water tank and flush it with distilled vinegar. Do not use bleach as it may damage its aluminum coating. Then scrub the dispenser nozzle and rinse the vinegar to not contaminate the water. Finally, you can clean the exterior of the dispenser at last.
How much does it cost to fix a refrigerator water dispenser?
Depending on the type of problem, the average cost of a refrigerator water dispenser ranges from $175 to $500.
How do you reset the water dispenser on a Frigidaire refrigerator?
Fill a glass of water by pressing it against the water dispenser lever. Empty it and repeat this for about four minutes. This will flush the water dispensing system and turn on the ice maker. Next, press and hold the Water Filter button for three seconds, and the filter status will be reset.
Conclusion
It is necessary to fix your refrigerator water dispenser as soon as possible if it does not work as it should. The above troubleshooting steps should have solved your Frigidaire refrigerator dispenser problems. But if you cannot solve it on your own, you need to get it inspected by an appliance repair technician.
As you may have figured out from above, replacing the water filter in your refrigerator for optimal use of the dispenser is necessary. According to the various models of filters, here’s how to carry out a KitchenAid refrigerator water filter change correctly.